Toote kirjeldus:
DC motor is a rotating motor that can convert DC electrical power into mechanical strength (DC motor) or mechanical power into DC electric powered vitality (DC generator). It is a motor that can transform DC and mechanical power into one yet another. When it operates as a motor, it is a immediate current motor, which converts electrical power into mechanical power when it runs as a generator, it is a immediate present generator, which converts mechanical strength into electrical power.
| Toote nimi | 50w 100w 150w 200w dc motor |
| Motor Variety | DC Motor,ACMotor,Stepper Motor,Asynchronous Motor ,Synchronous Motor (CZPT equipment) |
| Composition construction | The construction of DC motor should consist of two components: stator and rotor. The static element of DC motor is known as stator. The major perform of stator is to generate magnetic discipline, which is composed of foundation, principal magnetic pole, commutation pole, end cap, bearing and brush device. Working portion is named rotor, whose principal purpose is to make electromagnetic torque and inductive electromotive force. It is the hub of power conversion of DC motor. So it is also commonly known as armature, which is composed of rotor, armature main, armature winding, commutator and supporter. |
| Toode | ZSN,ZTP,Z4,Z2 |
| Working pace | Constant Speed /Reduced Speed /Adjust Velocity /Higher Speed Other |
| Primary classification | DC Motor is a equipment that converts mechanical power into DC electrical power. It is mainly used as DC motor for DC motor, electrolysis, electroplating, smelting, charging and excitation electricity source of alternator. Even though in locations the place DC electricity is needed, AC power rectifier is also utilized to convert AC into DC power, but from some aspects of efficiency, AC rectifier energy provide can not fully exchange DC generator. |
| Defense quality | IP55 |
| Thermal Course | a hundred and fifty five (F) |
| Taotlus | DC motors are extensively utilized in tape recorders, online video recorders, movie discs, electrical shavers, hair dryers, electronic watches, toys and so on. |
| Maintenance strategy | Specialist motor upkeep middle motor routine maintenance process: cleaning stator and rotor – replacing carbon brush or other elements – vacuum F pressure dipping paint – drying – Calibration stability. 1. Use environment must be always dry, motor surface area need to be stored clean, air consumption must not be hindered by dust, fibers and other obstacles. two. When the thermal security of the motor proceeds to operate, it need to be ascertained whether or not the fault arrives from the motor or the overload or the placing price of the protecting gadget is way too reduced. Soon after reducing the fault, it can be put into operation. 3, ensure that the motor is well lubricated for the duration of procedure. The standard motor runs for about 5000 hours, that is to say, lubricating grease need to be added or changed. When bearing overheating or lubricating deterioration is discovered in operation, the hydraulic pressure need to change lubricating grease in time. When changing grease, the old grease should be taken off, and the oil groove of bearing and bearing go over ought to be washed with gasoline. Then ZL-3 lithium grease ought to be crammed with one/two (two poles) and 2/three (4 poles, 6 poles and eight poles) of the cavity among the internal and outer rings of the bearing. 4. When the life of the bearing is in excess of, the vibration and sounds of the motor will boost obviously. When the radial clearance of the bearing reaches the pursuing benefit, the bearing need to be replaced. five, when removing the motor, it is Alright to remove the rotor from the shaft extension or the non extension finish. If it is not needed to unload the enthusiast, it is far more convenient to consider out the rotor from the non-axle extension conclude. When pulling out the rotor from the stator, the stator winding or insulation should be prevented from currently being broken. 6. When changing the windings, the type, measurement, turns and gauges of the first windings need to be recorded. When these info are dropped, they should be received from the manufacturer and the first developed windings should be transformed at will, which usually deteriorates one or many efficiency of the motor or even can make it unattainable to use them. |
