Jumbo Roll Paper Slitting Rewinding Machine

Jumbo Roll Paper Slitting Rewinding Device

Requirements:
one. It adopts Emerson PLC control method and 10″ touch display, all the operating parameters can be shown on the manage panel then the device will computerized work.
two. It adopts two sets of Yaskawa frequency inverter which is from Japan to make functioning device a lot more stable.
three. It adopts two sets of Fukuta inverter motor, which is from ZheJiang .
four. It adopts three sets fully automatic stress management to supply the continual stress to the end.
5. Computerized lift-up loading technique for hefty jumbo roll loading.
six. A established of photocell tracking technique imported from Germany.
seven. Computerized meter counter to quit the machine when it get to the pre-set size.
8. Air Blower and blower pipe for trimming the waste edge.

Specs
Categoria	Automatic Shaftless & Coreless Paper Slitter Machine
Application Materials	Standard Papers,Kraft Paper, Bond Paper, Paper Board,Non-woven Cloth, Movie, Aluminum Foil, CZPT Sheet etc.
Relevant Width of Axial / Substance	600mm ~ 2800mm /23.six-110″ (CZPTizable)
Min. Width of Slitting	10mm (Based on sorts of supply materials are utilized)
Max.Device Speed	300m/min (Relying on types of material applied)
Max.Unwinding Diameter	1500mm /59″
Max.Rewinding Diameter	1500mm(CZPTizable)
Tolerance of Slitting Width	±0.15mm(Dependent on types of materials utilized)
Max Applicable Fat of Material	4000 Kg (CZPTizable)
Rated Frequency	50Hz & 60Hz
Tensão nominal	380V,415V, 440V, 460V, 480V,or Dual-Voltage (CZPTizable)
Unwinding/Rewinding Shaft	Shaftless unwinder & Pneumatic Air Growing Shaft
General Proportions	2000 x 2500 x 1500mm
Excesso de peso	4000kg

 

Environmental Restriction
Localização	Indoor. The product ought to be installed   on flat and strong foundation.
Voltage Regulation	±10%
Frequency Regulation	±5%
Ambient Temperature	-5°C~40°C
Altitude	Not exceed a thousand Meters
Umidade Relativa	Less than 85% RH (Non-Condensation)

 

Componentes
Unwinding Section	-Shaftless unwinder,the cam dimension is 3”&6” -CZPT automatic raise-up loading system -Tech Mach analog EPC from Usa -RE Brake from Italy -Tech Mach Floating roller continual stress from United states of america -Tech Mach Sensor from United states of america -Self expandable chuck -Xihu (West Lake) Dis. & Slide AMT from ZheJiang
Slitting Area	-Alternatives of Razor cutter or Disc cutter -Disc Cutter Assembly undertake the cam self-locking -Cutter with adjustable and moveable blade foundation. -Meter counter
Rewinding Area	-three”air expanding rewinding corelessshafts -Middle Rewinding engineering -Force roller -Electromagnetic Clutch from ZheJiang
Managing Segment	-Siemens PLC & HMI from Germany -All the parametersare exhibited on the monitor -Minimal voltage electrical appliances all from Schneider
Trimmed Squander Edge	-Edge Waste Blower with Expulsion Tube
Opcional	-Friction Differential Shaft for rewinding. -Safety guard for the slitting device. -Crisis Switches on the 4 corner of device.

 

Configuration
Título	Modelo	Items	Observação
Computer Method	PLC(Siemens)+4DA+7”Touch Monitor(ZheJiang )+ Synchronic(Korea)	1Set	Siemens+ Weinview
Motor		2 Sets	FUKUTA From ZheJiang
Inversor de Frequência		two Sets	YASKAWA From Japan
Upper/Lower Round Knife		ten Sets	Jota CZPT
Brake			RE Brake from Italy
Sensor		2 Sets	Tech Mach Sensor from Usa
Pressure management		three Sets	Tech Mach Floating roller continual stress from United states
EPC		one Established	Tech Mach analog from United states of america
Chuck	Self expandable chuck	one Established	From ZheJiang
Photocell Monitoring		two Set	SIKC From Germany
Magnetic Clutch		two Sets	From ZheJiang
Low Voltage CZPTal Change			SCHNEIDER
Blower		one Set	China