Jumbo Roll Paper Slitting Rewinding Machine

Jumbo Roll Paper Slitting Rewinding Machine

Jumbo Roll Paper Slitting Rewinding Device

Requirements:
one. It adopts Emerson PLC control method and 10″ touch display, all the operating parameters can be shown on the manage panel then the device will computerized work.
two. It adopts two sets of Yaskawa frequency inverter which is from Japan to make functioning device a lot more stable.
three. It adopts two sets of Fukuta inverter motor, which is from ZheJiang .
four. It adopts three sets fully automatic stress management to supply the continual stress to the end.
5. Computerized lift-up loading technique for hefty jumbo roll loading.
six. A established of photocell tracking technique imported from Germany.
seven. Computerized meter counter to quit the machine when it get to the pre-set size.
8. Air Blower and blower pipe for trimming the waste edge.

Specs
Category Automatic Shaftless & Coreless Paper Slitter Machine
Application Materials Standard Papers,Kraft Paper, Bond Paper, Paper Board,Non-woven Cloth, Movie, Aluminum Foil, CZPT Sheet etc.
Relevant Width of Axial / Substance 600mm ~ 2800mm /23.six-110″ (CZPTizable)
Min. Width of Slitting 10mm (Based on sorts of supply materials are utilized)
Max.Device Speed 300m/min (Relying on types of material applied)
Max.Unwinding Diameter 1500mm /59″
Max.Rewinding Diameter 1500mm(CZPTizable)
Tolerance of Slitting Width ±0.15mm(Dependent on types of materials utilized)
Max Applicable Fat of Material 4000 Kg (CZPTizable)
Rated Frequency 50Hz & 60Hz
Rated Voltage 380V,415V, 440V, 460V, 480V,or Dual-Voltage (CZPTizable)
Unwinding/Rewinding Shaft Shaftless unwinder & Pneumatic Air Growing Shaft
General Proportions 2000 x 2500 x 1500mm
Excess weight 4000kg

 

Environmental Restriction
Location Indoor. The product ought to be installed   on flat and strong foundation.
Voltage Regulation ±10%
Frequency Regulation ±5%
Ambient Temperature -5°C~40°C
Altitude Not exceed a thousand Meters
Relative Humidity Less than 85% RH (Non-Condensation)

 

Components
Unwinding Section -Shaftless unwinder,the cam dimension is 3”&6” 
-CZPT automatic raise-up loading system
-Tech Mach analog EPC from Usa
-RE Brake from Italy
-Tech Mach Floating roller continual stress from United states of america
-Tech Mach Sensor from United states of america
-Self expandable chuck
-Xihu (West Lake) Dis. & Slide AMT from ZheJiang
Slitting Area -Alternatives of Razor cutter or Disc cutter
-Disc Cutter Assembly undertake the cam self-locking
-Cutter with adjustable and moveable blade foundation.
-Meter counter
Rewinding Area -three”air expanding rewinding corelessshafts
-Middle Rewinding engineering
-Force roller
-Electromagnetic Clutch from ZheJiang
Managing Segment -Siemens PLC & HMI from Germany
-All the parametersare exhibited on the monitor
-Minimal voltage electrical appliances all from Schneider
Trimmed Squander Edge -Edge Waste Blower with Expulsion Tube
Optional -Friction Differential Shaft for rewinding.
-Safety guard for the slitting device.
-Crisis Switches on the 4 corner of device.

 

Configuration
Title Model Items Remark
Computer Method PLC(Siemens)+4DA+7”Touch Monitor(ZheJiang )+
Synchronic(Korea)
1Set Siemens+ Weinview
 Motor 2 Sets FUKUTA From ZheJiang
Frequency Inverter two Sets YASKAWA From Japan
Upper/Lower Round Knife ten Sets Jota CZPT
Brake RE Brake from Italy
Sensor 2 Sets Tech Mach Sensor from Usa
Pressure management three Sets Tech Mach Floating roller continual stress from United states
EPC one Established Tech Mach analog from United states of america
Chuck Self expandable chuck one Established From ZheJiang
Photocell Monitoring two Set SIKC From Germany
Magnetic Clutch two Sets From ZheJiang
Low Voltage CZPTal Change SCHNEIDER
Blower one Set China

Jumbo Roll Paper Slitting Rewinding Machine