랙 앤 기어 방식의 공장 출고형 피니언 스티어링 장비를 개조할 때는 일반적으로 타이 로드 마감 부분을 조정해야 하는데, 이 타이 로드는 스티어링 휠과 바퀴를 연결합니다. 중국 기어랙 수출업체 그리고 피니언 어셈블리를 스티어링 너클에 연결합니다. 다음은 랙 앤 피니언 스티어링 장비를 조정하는 방법에 대한 표준 지침입니다.
Note: It is critical to check with the particular vehicle’s service manual for specific guidance and specifications, as the adjustment procedure can change based on the make and model of the car.
필요한 도구:
– Jack and jack stands
– Lug wrench
– Adjustable wrench or pliers
– Tape evaluate
권장 사항:
1. 준비:
– Park the car or truck on a stage surface and engage the parking brake.
– Securely increase the front of the car or truck making use of a jack and guidance it with jack stands.
– Get rid of the entrance wheels working with a lug wrench.
2. 타이로드 마감 상태를 점검하십시오.
– Visually inspect the tie rod finishes for any signals of wear, injury, or perform. If any factors are worn or ruined, they need to be changed right before trying adjustments.
3. 핸들을 중앙에 맞추십시오.
– Make sure the steering wheel is centered by on the lookout at the emblem or alignment marks on the steering wheel.
4. 토인(발가락 안쪽으로 향하는 각도)을 측정하세요.
– Use a tape measure to measure the length in between the front edges of the tires (recognised as the toe-in). Measure the distance at the front and rear of the tires.
– Review the measurements to the car manufacturer’s specifications for the sought after toe-in benefit. If the measurements are outside the advisable assortment, an adjustment is needed.
5. 타이로드 마감재를 변경하십시오.
– Loosen the lock nuts on the tie rod ends using an adjustable wrench or pliers. There is generally an altering sleeve between the internal and outer tie rod finishes.
– Rotate the altering sleeve to possibly lengthen or shorten the tie rod assembly, relying on the demanded adjustment.
– Change the sleeve in small increments, checking the toe-in measurement immediately after each individual adjustment right up until the ideal toe-in price is achieved.
– After the adjustment is finish, tighten the lock nuts on the tie rod ends to secure the location.
6. 토인 각도를 다시 확인하세요.
– Immediately after the adjustment, 다시 측정하다 토인 각도를 조정하여 제시된 범위 내에 있는지 확인하십시오. 필요한 경우 추가 조정을 하십시오.
7. 바퀴를 다시 설치하십시오.
– Put the front wheels again on to the vehicle and hand-tighten the lug nuts.
– Meticulously reduced the vehicle to the floor and tighten the lug nuts to the manufacturer’s specified torque employing a lug wrench.
8. 확인 및 검증:
– Commence the car and 중국 기어랙 수출업체 스티어링 휠을 양방향으로 돌려 스티어링 프로그램을 테스트하십시오.
– Get the car for a check generate to assure the steering feels responsive and the car tracks straight.
직접 조정하는 것이 불안하거나 필요한 장비가 없는 경우, 숙련된 정비사나 자동차 정비 전문가에게 조정을 맡기는 것이 좋습니다. 그래야 정확한 정렬과 안전한 조향 시스템 작동을 보장할 수 있습니다.