제품 설명
저장 탕천 기계설비 제조 유한회사는 2011년에 설립되었으며, 등록 자본금은 2,500만 위안입니다. 총 13.34헥타르 부지에 43,000제곱미터 규모의 작업장을 보유하고 있습니다. 회사는 주로 프리캐스트 콘크리트 요소, 특히 콘크리트 원심분리 말뚝 및 원심분리 기둥용 금형 및 장비의 연구 개발, 생산 및 판매에 주력하고 있습니다. 단순한 기계 공급을 넘어 부가가치 서비스를 포함한 통합 솔루션을 제공하여 고객이 손쉽게 생산을 시작할 수 있도록 지원합니다. 현재 한국, 베트남, 말레이시아, 방글라데시, 캄보디아, 인도네시아 등에 제품을 수출하고 있으며, 10개 이상의 해외 프로젝트를 성공적으로 수행했습니다.
저희가 언제나 고객님께 최고의 선택이 될 것이라고 확신합니다!
탕첸(Tang Chen)은 방적사 및 전봇대 생산에 특화된 방적기를 제조합니다. 변압기로 구동되는 이 방적기는 인간-컴퓨터 인터페이스를 통해 각 공정 단계별 방적 속도를 제어합니다. 따라서 정밀도가 높고 조작이 간편합니다. 또한, 당사는 축, 구동륜, 커플링, 베어링 받침대, 테이퍼 슬리브 등 다양한 종류의 방적기 부품 가공도 담당하고 있습니다.
명세서
| 아니요 | 프로젝트 | 단위 | 기술적 매개변수 | |
| 1 | 모터 | 비율 | kw | 45-132 |
| 회전 속도 | 분당 | 1000 | ||
| 2 | 주행 휠 직경 | mm | 600 | |
| 3 | 러닝 휠 중심 거리 | 축 방향 | mm | 2000 |
| 방사 방향 | mm | 1070 | ||
제조 공정
회사 소개
| 판매 후 서비스: | 1년 |
|---|---|
| 보증: | 1년 |
| 유형: | 운송 기계 |
| 숏크리트 종류: | OEM |
| 가공 공정: | 가공, 용접, 도장 |
| 구조: | 전기 모터 |
| 맞춤 설정: | 사용 가능 | 맞춤형 요청 |
|---|
모터 체인에서 흔히 발생하는 문제를 어떻게 해결하나요?
모터 체인에서 발생하는 일반적인 문제를 해결하려면 문제의 근본 원인을 파악하고 적절한 조치를 취해야 합니다. 다음은 모터 체인에서 발생할 수 있는 몇 가지 일반적인 문제와 해결 방법입니다.
1. Chain slipping or jumping: If the motor chain slips or jumps on the sprockets, it can indicate insufficient tension, worn-out sprockets, or a damaged chain. Check the tension of the chain and adjust it according to the manufacturer’s recommendations. Inspect the sprockets for signs of wear or damage and replace them if necessary. Additionally, examine the chain for any damaged or worn-out links and replace the chain if needed.
2. 과도한 소음: 모터 체인에서 과도한 소음이 발생하는 원인은 정렬 불량, 윤활 부족, 부품 마모 또는 부적절한 장력 등 다양합니다. 체인의 정렬 상태를 점검하고 필요한 경우 조정하십시오. 권장 윤활유를 사용하여 체인에 적절한 윤활유를 공급하십시오. 마모되거나 손상된 부품이 있는지 확인하고 필요에 따라 교체하십시오. 체인 장력을 적절한 사양으로 조정하십시오.
3. 체인 걸림 또는 멈춤: 작동 중 모터 체인이 걸리거나 멈춤 현상이 발생하면 정렬 불량, 이물질 축적 또는 윤활 부족 때문일 수 있습니다. 정렬 불량 여부를 확인하고 필요한 경우 체인과 스프로킷의 정렬을 조정하십시오. 체인이나 스프로킷에 쌓인 이물질이나 먼지를 제거하십시오. 마찰을 최소화하고 원활한 작동을 위해 체인에 적절한 윤활유를 공급하십시오.
4. Chain wear and elongation: Excessive chain wear and elongation can lead to poor performance and decreased efficiency. Regularly monitor the chain for signs of wear and measure its elongation using a chain wear gauge. If the wear exceeds the manufacturer’s recommendations, it is advisable to replace the chain with a new one.
5. 윤활 부족: 윤활이 부족하면 모터 체인의 마찰, 마모 및 조기 고장이 증가할 수 있습니다. 윤활 시스템을 점검하고 권장 윤활유로 체인이 적절하게 윤활되고 있는지 확인하십시오. 최적의 윤활을 위해 필요한 경우 윤활 빈도 또는 방법을 조정하십시오.
When troubleshooting motor chain issues, it is important to refer to the manufacturer’s guidelines and recommendations. If the problem persists or if you are unsure about the appropriate troubleshooting steps, it is recommended to consult a professional or the chain manufacturer for further assistance.
모터 체인을 올바르게 윤활하고 관리하는 방법은 무엇입니까?
모터 체인의 최적 성능과 수명 연장을 위해서는 적절한 윤활 및 유지 관리가 필수적입니다. 다음은 모터 체인을 올바르게 윤활하고 유지 관리하는 단계입니다.
1. 체인 청소: 윤활유를 바르기 전에 모터 체인에 묻은 먼지, 이물질 또는 기존 윤활유를 제거하십시오. 적절한 세척제와 브러시 또는 천을 사용하여 체인을 부드럽게 문질러 닦으십시오. 체인이 완전히 건조되었는지 확인한 후 다음 단계로 진행하십시오.
2. Choose the right lubricant: Select a lubricant specifically designed for motor chains. Consider factors such as the operating conditions, temperature, and load requirements when choosing the lubricant. Consult the manufacturer’s recommendations or seek professional advice if necessary.
3. 윤활유 도포: 모터 체인 전체에 윤활유를 고르게 도포하십시오. 적절한 도포기나 스프레이 병을 사용하여 윤활유가 충분히 도포되도록 하십시오. 체인과 스프로킷이 만나는 부분에 특히 신경 써서 도포하십시오.
4. 과도한 윤활유 제거: 윤활유를 바른 후 몇 분 동안 체인에 충분히 스며들도록 두십시오. 그런 다음 천이나 걸레로 과도한 윤활유를 닦아내십시오. 이렇게 하면 체인에 먼지와 이물질이 쌓이는 것을 방지할 수 있습니다.
5. 정기 점검: 모터 체인의 마모, 부식 또는 손상 여부를 정기적으로 점검하십시오. 체인의 늘어짐, 균열, 핀 손상 또는 과도한 유격이 있는지 확인하십시오. 문제가 발견되면 체인 교체 또는 손상된 부품 수리와 같은 적절한 조치를 취하십시오.
6. Tension adjustment: Check the tension of the motor chain regularly. Improper tension can cause excessive wear and reduce the chain’s performance. Follow the manufacturer’s guidelines or consult a professional to ensure proper tensioning.
7. 정기 유지보수 계획 수립: 모터 체인에 대한 유지보수 계획을 세우십시오. 여기에는 정기적인 청소, 윤활, 점검, 그리고 필요한 조정이나 교체가 포함됩니다. 체인을 최적의 상태로 유지하려면 계획을 철저히 준수하십시오.
이러한 단계를 따르고 정기적인 유지 보수를 유지하면 모터 체인의 성능과 수명을 극대화할 수 있습니다.
특정 모터에 맞는 모터 체인을 어떻게 선택하나요?
특정 모터에 맞는 모터 체인을 선택할 때는 여러 가지 요소를 고려해야 합니다. 다음은 단계별 가이드입니다.
1. Determine the motor specifications: Start by understanding the motor’s power rating, speed, and torque requirements. This information will help you choose a motor chain that can handle the motor’s power output and torque demands.
2. Identify the application requirements: Consider the specific application in which the motor will be used. Determine if the motor will be subjected to high loads, high speeds, or harsh environmental conditions. This will help you select a motor chain that is suitable for the application’s demands.
3. 체인 종류 결정: 모터 체인은 롤러 체인, 사일런트 체인, 부시 체인 등 다양한 종류가 있습니다. 각 체인 종류는 고유한 특성과 성능을 가지고 있습니다. 모터와 용도에 맞는 체인 종류를 선택하십시오.
4. Calculate the chain size: Determine the required chain size based on the motor’s power and torque requirements. Consider factors such as pitch size, roller diameter, and number of chain links. Manufacturers typically provide chain size charts or calculation tools to assist in selecting the right chain size.
5. 환경적 요인을 고려하십시오: 모터가 작동할 환경 조건을 고려해야 합니다. 모터가 습기, 화학 물질, 고온 또는 기타 가혹한 환경에 노출될 경우, 적절한 내식성, 내열성 및 내구성을 갖춘 모터 체인을 선택해야 합니다.
6. Consult manufacturer recommendations: Consult the motor manufacturer’s recommendations or specifications to identify any specific requirements or restrictions for motor chains. They may provide guidance on compatible chain types, lubrication requirements, and maintenance recommendations.
7. 비용 및 가용성 평가: 선택한 모터 체인의 비용과 가용성을 고려하십시오. 초기 비용, 유지 보수 요구 사항, 예비 부품 또는 교체품의 가용성과 같은 요소를 평가하십시오.
By considering these factors and conducting thorough research, you can select the right motor chain that matches the motor’s specifications, application requirements, and environmental conditions. It is recommended to consult with motor and chain manufacturers or industry experts for further guidance and assistance.
editor by CX 2023-10-07